Confor Form (formerly called Temperfoam) is the conforming foam cushion that was developed for the “Astronaut’s Couch” back in the Apollo space program. Confor Foam has the capability of absorbing a tremendous amount of impact shock compared to common polyfoam and it is flame resistant. It is an excellent product that will give your seats enduring comfort that you never thought possible. Adapts to you for pressure point-free comfort that is really incredible. The best universal cushion for aircraft use is a 3” CF42/CF45/CF47 laminate. Confor Foam meets FAR 25.853, FAR 25.855, and CAL 117 burn specifications making it excellent for certified aircraft or homebuilts. Some special sizes in 1”, 2”, or 3” thicknesses are available on special request.
Specifications:
Part No. 01-09310: 1" X 16" X 18" Part No. 01-09320: 2" X 16" X 18" Part No. 01-09300: 3" X 16" X 18"
Nylon Polypenco. pressure tubing is a super tough, low friction, high flexibility tubing that can be used for cable protectors or in short pieces, as small bushings and washers.
Suitable for use in oil, air, vacuum, fuel and low pressure hydraulic lines. It resists abrasion and wears better than aluminum or steel tubing. Has an extremely smooth inner surface with a very low coefficient of friction. Used for brake lines, and also as a conduit for the rudder cables in the Rutan VariEze and Long-EZ. Rated 1000 psi. Sold by the foot.
Use Poly-Flo fittings with standard wall tubing.
Click here for the Poly-Flo fittings webpage.
Note: Poly Flo fittings cannot be used with High Burst Pressure tubing.Must use SAE fittings
Good-grade neoprene. Soft, flexible, oil-resisting.
This neoprene coated pyroglass cloth is designed for applications where its superb heat and flame resistance provides an extra margin of protection for people and equipment. Self-extinguishing, it is used as aircraft firewall barriers, protective sleeves and tadpole tape covers, flat seals, gaskets, mounts and door seals. It is ozone and weather resistant and can be used against caustics, gasoline, oil, water and steam. It does not support combustion and will operate in continuous temperatures from -40F to +200F.
The A series firewall fitting is all aluminum and requires only one hole in the firewall. It has a 1 inch aluminum ball with a swivel angle up to 50 degrees from straight. It is held on the firewall with one 1 5/16 aluminum nut.Assembly weighs only 1.3oz-1.5oz (.08lb-.09lb) depending on ball hole size.Ball hole sizes available are .125, .188, .218, .240, .250, .260, .330, .375, .438 and .500.Order example: TTP-125A (.125 ball hole)
The A series firewall fitting is all aluminum and requires only one hole in the firewall. It has a 1 inch aluminum ball with a swivel angle up to 50 degrees from straight. It is held on the firewall with one 1 5/16 aluminum nut.
Assembly weighs only 1.3oz-1.5oz (.08lb-.09lb) depending on ball hole size.
Ball hole sizes available are .125, .188, .218, .240, .250, .260, .330, .375, .438 and .500.
Order example: TTP-125A (.125 ball hole)
This silicone rubber is excellent for replacement of baffle seals as it exceeds asbestos type seals in durability and flexibility over its entire operating heat range of -80 F to +425 F. Meets Mil Spec ZZR765B. ISR3 meets Mil Spec AMS3303 (PN 05-00810, 05-00811, 05-00811-3) AMS3320 for all other. Available in red, blue & black.
This silicone rubber is excellent for replacement of baffle seals as it exceeds asbestos type seals in durability and flexibility over its entire operating heat range of -80 F to +425 F. Meets Mil Spec ZZR765B. ISR3 meets Mil Spec AMS3303 (PN 05-00810, 05-00811, 05-00811-3) AMS3320 for all other. Available in red, blue & black.
#4: 1-1/4" wide with an 1/8" x 1/2" long groove, manufactured in 12ft lengths.#7 Neoprene sponge rubber 1/4-round door seal. 1/2” Legs, 3/4” Curve, 3/8” Radius. Hollow core makes a better seal. Manufactured in 25 Ft. lengths.
Made of 304 stainless steel. All measurements are in inches
These ball and socket air vents are injection molded T grade ABS. The vent orifice is 1" diameter, and the ball swivels 45°. The mounting flange is 2-1/8" square, and the distance between mounting hold centers is 1- 11/16". Mounts in 1.75" diameter hole & uses 1-3/4" ducting.
These ball and socket air vents are injection molded T grade ABS. The vent orifice is 1" diameter, and the ball swivels 45°. The mounting flange is 2-1/8" square, and the distance between mounting hold centers is 1- 11/16". Mounts in 1.75" diameter hole & uses 1-3/4" ducting.
Nylon Polypenco. pressure tubing is a super tough, low friction, high flexibility tubing that can be used for cable protectors or in short pieces, as small bushings and washers.Suitable for use in oil, air, vacuum, fuel and low pressure hydraulic lines. It resists abrasion and wears better than aluminum or steel tubing. Has an extremely smooth inner surface with a very low coefficient of friction. Used for brake lines, and also as a conduit for the rudder cables in the Rutan VariEze and Long-EZ. Rated 1000 psi. Sold by the foot.Use Poly-Flo fittings with standard wall tubing. Click here for the Poly-Flo fittings webpage.Note: Poly Flo fittings cannot be used with High Burst Pressure tubing.Must use SAE fittings
Applications: Light to medium duty linkage, including:
Cable assemblies Light industrial applications Racing throttle links.
Applications: Light to medium duty linkage, including: Cable assemblies Light industrial applications Racing throttle links.
Button Type Dash Control designed for use with many control system applications. Easily installed. Operates smoothly. All adjustable parts are metal. 7/8" Dural button on 3/16" diameter shaft. Maximum travel is 2". Furnished in 5 ft. and 8 ft. length. May be shortened. Order Inserts separately.
Round pressure-sensitive labels, 3/4-Inch diameter. White lettering on black background.
T-Handle dash control manufactured of duralumin and brass. Locks positively, will not vibrate loose. One-fourth turn locks it in any position and will hold up to 100 lbs. Standard travel 2-1/2". T-handle is 1-3/4" wide. Can be mounted from front or rear of instrument panel. Complete with wire and casing which may be shortened.
Spiral-wound galvanized wire casing. Use for push-pull controls of any length. Inside cable dia. .078. Outside casing diameter 7/32. This includes the inner wire (p/n 05-15510) and the outer housing/casing.
These quality quadrants have been in use for over 35 years in a wide variety of experimental and ultralight aircraft. All quadrants are made with AN standard hardware and aircraft-quality 6061-T6 or 2024-T3 Aluminum. All sizes and models can be utilized for a side mount, center mount, or dual-control hookup. Can be used in Pitts, Cub, Aeronca, Bakeng Deuce, Horizon 2, Dakota Hawk, Quicksilver, Mini Max, Dragonfly, X-Air, etc. If you have an aircraft, we have a quadrant that will fit your needs.
Model #1 -This external reversing quadrant is our most popular for dual-control hookup. It can also be used as a single hookup. Available in S-series only. One, two or three levers. Friction or non-friction.
Four sizes available: Special series quadrants:Large Series 4-78" wide x 4" tall. 13 oz.Standard Series 4" wide x 3-1/2" tall. 11 oz.3/4 series 3-7/8" wide x 3" tall. 10 oz.1/2 series 3-7/8" wide x 2-5/8" tall. 8 oz. RV-series 4" wide x 4" tall. 12 oz.Panel Mount 4" wide x 3-1/2" tall 12 oz.Twin Engine 4-7/8" wide x 4" tall 15 oz.All weights are for two arms and friction. (Except twin engine).Measurements do not reflect Lever lengths.
These quality quadrants have been in use for over 35 years in a wide variety of experimental and ultralight aircraft. All quadrants are made with AN standard hardware and aircraft-quality 6061-T6 or 2024-T3 Aluminum. All sizes and models can be utilized for a side mount, center mount, or dual-control hookup. Can be used in Pitts, Cub, Aeronca, Bakeng Deuce, Horizon 2, Dakota Hawk, Quicksilver, Mini Max, Dragonfly, X-Air, etc. If you have an aircraft, we have a quadrant that will fit your needs.
Model #2 - This internal non-reversing hookup quadrant is often used on the RV series and similar aircraft. Available in all four sizes with one, two or three levers. Friction or non-friction. L-series can achieve a throw up to 2-5/8".
Four sizes available: Special series quadrants:Large Series 4-78" wide x 4" tall. 13 oz.Standard Series 4" wide x 3-1/2" tall. 11 oz.3/4 series 3-7/8" wide x 3" tall. 10 oz.1/2 series 3-7/8" wide x 2-5/8" tall. 8 oz. RV-series 4" wide x 4" tall. 12 oz.Panel Mount 4" wide x 3-1/2" tall 12 oz.Twin Engine 4-7/8" wide x 4" tall 15 oz.All weights are for two arms and friction. (Except twin engine).Measurements do not reflect Lever lengths.
WIRE GRIP - Is a unique fitting which securely attaches to solid wire end push-pull cables. Uses a "pin vice" gripping action to attach a cable. The 5/8" long 10-32 threaded end will attach a clevis, ball joint, or other hardware for use with mixture controls, carb heat box, cabin air, or other applications, resulting in a clean, professional installation.Note: Use PN 05-16001 on A790 ACS controls.
WIRE GRIP - Is a unique fitting which securely attaches to solid wire end push-pull cables. Uses a "pin vice" gripping action to attach a cable. The 5/8" long 10-32 threaded end will attach a clevis, ball joint, or other hardware for use with mixture controls, carb heat box, cabin air, or other applications, resulting in a clean, professional installation.Note: Use PN 05-16001 on A790 ACS controls.
WIRE GRIP - Is a unique fitting which securely attaches to solid wire end push-pull cables. Uses a "pin vice" gripping action to attach a cable. The 5/8" long 10-32 threaded end will attach a clevis, ball joint, or other hardware for use with mixture controls, carb heat box, cabin air, or other applications, resulting in a clean, professional installation.Note: Use PN 05-16001 on A790 ACS controls.
A Safe "No-Slip-Grip" for your thru-bulkhead cables. This unit prevents your throttle mixture, choke or any push-pull cable from slipping at the firewall/ bulkhead location. Machined from lightweight aluminum, and blue anodized. Installation is simple with a drill and wrench. Once installed, the cable is threaded and the end nut is snugged down on the cable casing for positive encapsulation. Designed specifically for the aircraft industry, these fittings can be installed on virtually any application that requires a solid hold on any cable assembly with a rigid outer case. Thousands of applications: auto, boat, race car, motorhome. Used with 1/4" thru 7/32" diameter cable.
This fitting eliminates the need to put an angle fitting on standard adapter. 1/4" female pipe thread on side and bottom & 1" male pipe or 3/4" male pipe on bottom. Use with AN867-6 or 8
Protect the spherical bearing of rod ends. This patented design features a neoprene rubber seal bonded directly to an aircraft quality washer. The seal encapsulates the bearing and flexes accordingly with any change in angularity. This provides unprecedented protection from dirt and other types of contamination which may severely shorten the life of these important components. The rubber is engineered for wide range of temperature variation and is impervious to gasoline, oils, and most other common fluids. The steel washer is plated for protection from corrosion.
This cabin box is our first modification to our standard heat box. The only difference between this and the standard is that the deluxe cabin heat box has one inlet and two outlets; the second outlet must be used to dump and route, via 2" scat tube, the warm air away from the low plenum area when heat is not being used in the cabin. (It is very important not to run the dump tube to another box on the other side of the firewall, because a constant flow of air is necessary to ensure that the heat muff does not overheat.) The weight on this unit is 5.5 ounces.
2” ALUMINUM FLANGE - Accepts 2” scat tube. Flange allows riveting to firewall, baffles, etc. Wt: 0.2 oz
Polyurethane Protective Tapes couple an extremely tough and durable thermoplastic elastomer with an acrylic adhesive in a self adhering tape construction that can be quickly and easily applied to form a long lasting protective surface for your product and/or equipment. It combines a number of unique properties that make the product extremely effective at preventing damage caused by abrasion, erosion, minor impact, and fluids.
These Tapes are: Extremely Tough and Durable, Providing Long Service Life. Puncture and Tear Resistant; Preventing Fluid Penetration Conformable to compound curvatures; Can Fit Most Shapes Fast and Easy to apply; Saves on Installation Labor A Solvent Free Surface Protection Solution; Environmentally Responsible. Used extensively in Aerospace, Transportation, Marine, Construction, and General Industrial applications
ISD Chafe Tape is a durable Teflon material with a pressure sensitive adhesive which resists solvents, and oils. Designed specifically to prevent aluminum chafing between airframes and engine cowls. It helps prevent black streaking on aircraft exterior due to cowl chafing. It's not FAA/PMA approved. Operable temperature range: -100F to +500F. Width: 1". Roll length: 6 yds. Tkns: .012
Over 200 pressure sensitive labels and words conveniently grouped for ease of transfer to airplane controls or instrument panel. Available in two type sizes (see illustration) and in black or white lettering (specify). Large Size is 1/8" Small size is 1/16"
This material is excellent for reducing noise levels in all types of certificated and home built aircraft. It is a closed cell vinyl insulating material which will not absorb water or oil. Has fire retardant qualities and meets FAR 25.853a Appendix F, Pt1. It is smooth on one side for easy attachment to the inside cabin skins, sides, top and front firewall.Excellent for helicopters as well. Furnished in bulk 48" wide sheet, it is easily cut by scissors and attached with contact cement. Available in black only.
